Analysis of malic acid, residual sugar, volatile acidity and ammonia is very important in quality control during wine production. Enzymatic assays carried out in microplate format are quantitative and help achieve high throughput with respect to time and labor. The residual sugar assay involves enzymatic conversion of the analytes to give NADPH as a by-product. Measuring NADPH production by measuring absorbance at 340 nm allows direct quantitation of the analytes in wine samples. Here we describe the use of Molecular Devices SpectraMax® Plus 384 Microplate Reader and SoftMax® Pro Software to efficiently collect and analyze the data for enzymatic determination of residual sugar in wine.
Some of the unique features of the SpectraMax Plus 384 Microplate Reader are:
- Wavelength Range: 190–1000 nm in 1-nm increments with no need for separate filters; covers UV range
- Read Speed: 96 wells: 9 Seconds
384 wells: 29 Seconds
- Temperature: 4°C above ambient to 45°C
- Cuvette port: Holds standard cuvettes and 12 x 75 mm test tubes
- OD range: 0–4 OD
Enzymatic measurement of residual sugar (RS) in wine
(1) Glucose + ATP Glucose-6-Phosphate + ADP
(2) Fructose + ATP Fructose-6-Phosphate + ADP
(3) Fructose-6-phosphate Glucose-6-Phosphate
(4) Glucose-6-phosphate + NADP Glucose acid-6-phosphate + NADPH + H+
PGI: Phosphoglucose isomerase
This assay measures the two major sugars in wine, glucose and fructose. Since the formation of NADPH is stoichiometrically related to the oxidation of glucose-6-phosphate, measurements for glucose + fructose can be determined by the absorbance of NADPH at 340 nm.
The PathCheck Sensor is a temperature independent feature from Molecular Devices that measures the optical pathlength of samples in microplate wells. It is an innovative way of normalizing the absorbance reading in a microplate well to that of a 1-cm cuvette..
Beer-Lambert Law states that Absorbance = E * C * L
E = absorptivity (extinction coefficient)
C = concentration
L = pathlength
In case of a cuvette, the optical path is horizontal, thus the pathlength is fixed and is equal to 1 cm. But in case of a microplate, the optical path is vertical. So, the pathlength depends on the volume of the sample, as illustrated in Figure 2.
SoftMax Pro Software
The software controls the instrument, collects the data, and provides complete data analysis. Customized protocols with appropriate instrument settings and calculations can be pre-written and saved. The end user can conveniently open a preconfigured protocol and obtain complete results and analysis with no protocol setup time.
- SpectraMax Plus 384 Microplate Reader (Molecular Devices cat. #PLUS 384)
- UV-transparent 96-well microplates (Corning cat. #3635)
- Transferpette micropipette (Drummond Scientific cat. #2704174, 2705402, 2705412, 2704180; Drummond Digital Microdispenser cat. #3-000-510)
- Microtips for the micropipettes (Eppendorf cat. # epT.I.P.S. Reloads 022491539, 022491512, 022491547)
- Centrifuge for microfuge tubes (Eppendorf cat. #5424)
- Microfuge tubes 1.5 mL capacity (Eppendorf cat. #022364111, 022363557, 022363514, 2236357-3)
- D-Fructose (Fisher Scientific cat. #L95-500)
- Hexokinase/Glucose-6-Phosphate Dehydrogenase 30 mg (10 mL, Roche cat. #10737275001)
- Phosphoglucose isomerase 10 mg/mL (Roche cat. #10128139001)
- Polyvinyl pyrrolidone (Fisher Scientific cat. #BP431-100)
- TRIS (Amresco cat. #0497-500G)
- MgSO4 • 7H2O (Fisher Scientific cat. #M63-500)
- ATP (Boehringer Mannheim cat. #10519987001)
- NADP (Boehringer Mannheim cat. #10240354001)
- 1.0 M HCl (Fisher Scientific cat. #SA431-500)
Preparation of fructose standards
The reagents were stirred until dissolved. Standards producing a standard curve with coefficient of determination (R)=1.000 were stored in 1.5 mL freeze tubes at -4°C. Reagents that are too old may not give an ideal standard curve.
|Concentration||0.1 g/100 mL||0.2 g/100 mL||0.4 g/100 mL|
|DI H2O||95 mL||95 mL||95 mL|
|D-Fructose||0.1 g||0.2 g||0.4 g|
|Bring Volume To||100 mL||100 mL||100 mL|
Preparation of RS buffer solution
Polyvinyl pyrrolidone (PVP) 2.0 g, TRIS 3.0 g and MgSO4 • 7H2O 0.5 g were added to 350 mL deionized (DI) H2O in a 400-mL beaker. The pH of this solution was adjusted to 7.6 with 1.0 M HCl (≈36 mL). Further, ATP 0.15 g and NADP 0.175 g were then added to this solution, and the volume was adjusted to 500 mL with a volumetric flask. The buffer was stored at 4°C.
Processing of wine samples for the RS assay
If necessary, wine samples were diluted in DI water according to Table 2. Turbid samples were centrifuged or filtered prior to analysis, either before or after dilution. Samples diluted in DI water 1:10 were accompanied by 4.0 g/100 mL standard diluted 1:10. Samples diluted in DI water 1:100 were accompanied by 10.0 g/100 mL standard diluted 1:100.
|Assay Limits||Dilution||Sample Volume|
|0.01-0.4 g/100 mL||No Dilution Required||5 µL|
|0.4-1.0 g/100 mL||No Dilution Required||5 µL|
|1.0-4.0 g/100 mL||1:10 Dilution||5 µL|
|4.0-40.0 g/100 mL||1:100 Dilution||5 µL|
Step 1: Blanks, standards and samples were run in duplicate.
|Reagent Blank||Buffer 300 µL||DI Water 5 µL|
|Standards||Buffer 300 µL||Standards 5 µL|
|Samples||Buffer 300 µL||Samples 5 µL|
Step 2: D-Fructose standards were removed from the freezer and allowed to warm to room temperature.
Step 3: The amount of buffer necessary to analyze standards and samples was measured out into a dedicated “RS” beaker and warmed to room temperature. This step is necessary for achieving an ideal coefficient of determination.
Step 4: Phosphoglucose isomerase (PGI) enzyme was added to the buffer according to the values in Table 3. PGI was mixed into buffer thoroughly, but gently to avoid denaturing the enzyme.
|Amount of Buffer Required||Amount of PGI Added|
|10 µL||14 µL|
|50 µL||28 µL|
|100 µL||56 µL|
|150 µL||84 µL|
|200 µL||112 µL|
Step 5: 300 µL of buffer was dispensed into each well using the 300-µL multichannel pipette.
Step 6: 5 µL of DI H2O, standard, or sample was dispensed into the appropriate wells.
Step 7: The reagents were mixed by pipetting up and down (trituration).
Step 8: The plate was mixed by vortexing for 30 seconds; an initial absorbance reading was then taken on the microplate reader.
Step 9: Immediately after the initial read, 5 µL of HK/G6P-DH was dispensed into each well using the 1–20 µL multichannel pipette.
Step 10: The plate was mixed by vortexing for 30 seconds and incubated at room temperature for 21 minutes.
Step 11: After 21 minutes of incubation a “Final” reading was taken with the same instrument settings on the microplate reader.
The instrument was programmed through SoftMax Pro Software. The settings were adjusted in the plate section of the software (Figure 4). Table 4 shows the instrument settings used for the RS assays. Figure 4 shows screenshots for the wavelength settings and “PathCheck” selection.
|PathCheck||PathCheck selected, Water Constant (no plate background constant)|
|Automix & Blanking||Off|
|Assay Plate Type||96-Well Standard|
|Strips||Selected as needed|
Two identical plate sections were created. The initial plate section involved reading the plate with all the reagents but no enzyme. The second plate section was the actual reaction with enzyme. The optical density readings from the initial plate section were subtracted from the optical density readings of the second plate section through reduction settings.
Template setup for RS assay
A template was set up in the software to denote placement of the standards and samples in wells of the microplate. The flexible template layout allows easy addition of more samples and replicates. For the initial plate, no template was set up. For the final plate, standards and unknown samples were assigned. Concentration of each standard was assigned by clicking on the wells and typing the appropriate concentration in the box. The range was 0–0.4 g/100 mL (Figure 5).
The final plate was the actual reaction with the enzyme. The optical density readings from the initial plate were subtracted from the optical density readings of the final plate through reduction settings (Figure 6). Hence the plate blank was not used. A plate blank was incorporated in the experiment for quality control.
The experiment was performed as described in the Materials and Methods section. A baseline reading was taken with the plate containing all the components of the reaction mixture except the enzyme (Figure 7, Panel A). After adding the enzyme to the reaction mixture, the plate was incubated for 21 minutes at room temperature and a final reading was taken (Figure 7, Panel B).
SoftMax Pro Software automatically calculated mean, standard deviation, and %CV for the standard and tabulated the results in a group section (Figure 8).
A standard curve was created using information from group section “STD” with concentration on the x-axis and mean OD value of the replicates on the y-axis (Figure 9). Standard deviation was used to denote the error bars, while a linear curve fit was assigned to the plot. The standard curve was used in determining the residual sugar concentration in wine samples denoted as “Unknown.”
A group section designated as “Unknown” was populated automatically with data from samples designated as “Unknown” in the template.
Residual sugar in each sample was calculated by the software using the standard curve for interpolation (Figures 10 and 11).
The SpectraMax Plus 384 Microplate Reader is a good choice for running enzymatic quantitative measurement of residual sugar (RS) and Malate (ML) in wines and can be extended to similar assays, including ammonia and volatile acidity measurement.
Advantages include the following:
- Direct quantitation of analytes in wine samples
- Improved throughput relative to traditional single-tube methods
- Automated calculation of results with SoftMax Pro Software
- It is cost- and time-effective.
- Tunability and the PathCheck Sensor features of the SpectraMax Plus 384 reader aid in reaching higher precision and accuracy.
- SoftMax Pro Software is a convenient tool for analysis and calculation of complicated and large data sets. It offers pre-written, ready-to-use protocols, custom formulas and appropriate graphing options.
- Other Molecular Devices readers with absorbance detection mode, e.g. the SpectraMax i3x Multi-Mode Microplate Reader, may also be used for this application.
- For increased throughput requirements, Molecular Devices StakMax® microplate handling system integrates with SpectraMax readers to enable automated processing of batches of 20, 40, or 50 microplates.